Jen-Ken AF3P Vitrigraph Glass Kiln
Compact and portable for a kiln, this vitrigraph kiln has a hole in the bottom that is used to pull stringers from.
Inside measures 9" wide x 9" long x 9" deep. This kiln is side firing only. Kiln comes as a three piece or can be all attached with a hinged lid with a special order. This kiln can be converted for fusing or ceramics with the purchase of the optional second solid floor with no hole in the bottom.
This kiln is design as is to only be a vitri kiln and to be fired on a steel rack as shown. Please seek proper instruction before attempting to fire the kiln and pull stringer.
Do not use a vitri kiln on a table. Glass flows out the hole once the kiln reached about 1650F. Proper clothes, tools, high temp gloves, and a suitable area with a rack and large steel container to catch the hot glass are highly recommended.
This kiln comes standard with the Orton Digital 3-key controller.
Solid State Relay
A Solid State Relay is hands down the best investment you can make in your kiln!
The relay is what controls the power cycling of the elements in the kiln and they need to be able to withstand a ton of power as they do so. The solid state relays are incredibly efficient compared to the standard mechanical relays and are able to operate at much faster speeds. What this equates to is incredibly tight temperature control for accurate firings, longer element life, and savings on your electrical bill!
The standard mechanical relays have moving parts which cause wear and tear over the years and will eventually need to be replaced; however with a solid state relay it's likely to last the entire life of the kiln! You willsave money and time by never needing to worry about this in the future!
Furniture kit recommended for use with Jen-Ken Vitrigraph Glass Kiln
- One (1) 8" Square Shelf
- Assortment of Shelf Posts
* Received shelves may contain surface imperfections such as scratches, discoloration or rough edge. These possible imperfections are understood and accepted by the buyer.
* This furniture kit is only needed if ordering the solid floor
Bring your kiln to new heights... literally!
Increase accessibility to your kiln, give it some room to breathe, and make sure it's looking it's best for you every single day.
|Max Temperature||2000 °F|
|Inside Dimensions||9" x 9" x 9"|
|Volume (Cu. Ft.)||0.42|
|Power Plug Type||NEMA 5-15|
|Shipping Weight (lbs.)||70|
|Product Weight (lbs.)||50|
|Shipping Lead Time||Made To Order - Please Inquire|
My vitragraph kiln arrived badly damaged. I sent pictures to Soul Ceramics, they immediately contacted me and arranged to send it back. The kiln manufacturers are very backed up at this time but Soul Ceramics had a new one at my studio in less than two weeks. It is so nice to do business with a company like this. My experience with Olympic was and is a huge waste of time and money. Thank you Soul Ceramics.
* Reviews may be for a similar product in the same series, but a different size.
At Soul Ceramics, we want our customers to know they are getting the best prices online. When you see the blue "Lowest Price Guarantee" words on our website, we are guaranteeing that we have the lowest price anywhere on the internet. In fact, if you find another online store that offers a lower price then us within 30 days of your purchase date please let us know and we will hand you the difference - in cash. We want you to shop confidently knowing that you are getting the absolute best price on your kiln or wheel.
To request your partial refund, e-mail us a link to the same product on our competitor's website within 30 days from the date of your order and we will process the credit accordingly.
Our Lowest Price Guarantee has some restrictions:
- You must purchase the item from our website before requesting your partial refund
- Special promotion offers are not eligible
- The competitor must be an online store only
- The website can not be a discounter or auction website, such as eBay
- The competitor must be an Authorized Retailer for the product
- The price on the competitor's website must include all shipping and processing fees
- The model must be "like-for-like" (eg: In-stock vs. In-stock or Made-to-order vs. Made-to-order)
- The manufacturer must be either Evenheat Kiln, Jen-Ken Kilns, or Paragon Industries
At Soul Ceramics, we know how annoying it can be when you are hit with hidden costs and fees when you purchase items online. That's why we offer FREE SHIPPING* on all standard orders through Soul Ceramics.
We even cover extra costs such as lift gate service, so the price you see is the price you pay!
For the full details on this offer and our detailed shipping and returns policies, click here.
* Non standard orders include shipments outside of our standard shipping range, and orders that do not include a kiln or pottery wheel in the same shipment. Soul Ceramics reserves the right to inform you of shipping costs before orders are finalized.
SOUL CERAMICS LLC EDITOR'S NOTE
The below warranties were taken from the the respective manufacturers and last updated on June 4, 2018. Please note that these below warranties are all for reference only. While we do our best to keep these up to date; the manufacturer has the final say in what their product is warrantied as. Please reference your owner's manual upon purchase, or contact the manufacturer directly if you would like further clarification.
Please scroll to the appropriate manufacturer's warranty for your kiln.
Extended Warranty (Provided by Clyde)
All Clyde warranties are for the core product only. In the case of any kilns/ovens where additional product options are available (Controllers, furniture kits, stands, blade fixtures, vents, etc.) the warranty does not apply, and the warranty would only be applicable to the kiln/oven.
Evenheat Kiln, Inc. warranty
Evenheat Kiln, Inc. guarantees to the original purchaser that for a period of two full years (one year for Evolution Series fiber lids) from the date of purchase the kiln will be free of defects in workmanship and materials when used under normal and proper operating conditions. Evenheat will replace or repair any defective part as specified.
FOR THE WARRANTY TO BE EFFECTIVE THE PURCHASE MUST:
Provide written proof of date of purchase. (Warranty card sent in at time of purchase.)
Notify the Evenheat Distributor/Dealer from whom the kiln was purchased, within 10 days after defect has been discovered.
Make kiln immediately available for inspection.
FOR WARRANTY REPAIRS:
Warranty repairs should be handled through the Distributor/Dealer from whom the kiln was purchased, who will arrange for any repairs or replacement of parts under the terms of this warranty upon receipt of the kiln (or defective part). Otherwise the defective part may be returned (postage prepaid) to Evenheat Kiln, Inc. P.O. Box 399 6949 Legion Drive Caseville, MI 48725. If, after factory examination, the original part is found to be defective, a new or repaired part will be shipped prepaid by Evenheat Kiln, Inc.
If the entire kiln is to be returned to the factory, all transportation costs will be borne but he purchaser. The purchaser should notify Evenheat Kiln, Inc. (989) 856-2281 prior to shipping. Evenheat will help advise the best shipping method and if it is necessary to return the entire kiln or only certain parts. Warranty work will be performed within 30 days after defective part is returned to the factory.
Evenheat Kiln, Inc. reserves the right, at its option, to replace the entire kiln or any part of it in order to fulfill its obligation under this warranty.
THIS WARRANTY DOES NOT COVER:
Freight damage, kilns altered in any way, abuse or neglect, moisture, improper storage or installation.
Kiln overfired (reaching temperature higher than melting point of ware inside kiln) regardless of cause.
Dawson Kiln Sitter or Limit Timer.
Kilns operated on incorrect voltage.
Improper electrical installation.
Kiln furniture or ware.
Kilns used for reduction or salt firing.
Kilns used for purposes other than the firing of glass materials.
Kilns operated in excess of the cone or temperature on the rating plate.
Damage to Property or personal injury that may occur from kilns that are fired on or near wood floors or combustibles.
Damage to property or personal injury that may occur from improper ventilation of the work area and building structure.
This warranty is in lieu of all other warranties, expressed, or implied.
Evenheat Kiln, Inc. neither assumes nor authorizes any Distributor/Dealer, Retailer or employee to assume for it any other obligations or liabilities in connection with Evenheat Kilns.
This warranty is limited as specified above and excludes incidental or consequential damages. Some states or providences do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
Evenheat Kiln, Inc.
P.O. Box 399
6949 Legion Road
Caseville, MI 48725
United States of America
Speedball Art Products warranty
Your Speedball Art Products Company purchase comes complete with either a 2-YEAR, 5-YEAR, or 10-YEAR WARRANTY (100% parts & labor when labor performed at Speedball Factory) depending on the product purchased - please review the product page. Speedball Art Products Company warrants this Speedball pottery wheel to be free from defects in materials and workmanship under normal use and service, that would affect its operation for a period of 10 (ten) years from the date of purchase.
This wheel must be registered within 30 (thirty) days of the date of purchase to make the warranty effective. Registration can be performed either online at http://speedballart.com/warranty_form.php or by contacting our Customer Service Department at 800.898.7224. The obligation of this warranty shall be limited to repairing or replacing any part of the wheel which, at the discretion of the Company, shall be proven defective in materials or workmanship under normal use and service during the time period commencing with the date of purchase. Full wheel replacement will be at the discretion of the Company and will only be considered for claims initiated within 30 (thirty) days of purchase.
This warranty does not apply to:
Damage caused by accident, abuse, mishandling or dropping.
Units which have been subject to unauthorized repair.
Units not used in accordance with direction.
Damage exceeding the cost of the product.
Damage by flood, lightning or natural disaster, war declared or undeclared.
In no case shall the Company be liable for any incidental or consequential damages for breach of this or any other warranty, express or implied, whatsoever.
The limit of this warranty includes the product only and not any loss of work time or contract due to inability to use the wheel.
Parts in need of repair shall be returned by the customer, shipping prepaid, to:
Speedball Art Products
2301 Speedball Road
Statesville, NC 28677
After any repair or replacement, Speedball Art Products Company will return under normal working schedule and by UPS/FedEx Ground Service (for customers in the Continental United States). Rush repair orders are accepted by purchase order and credit card payment or COD charges. Shipping charges for rush returns other than UPS/FedEx Ground Service must be prepaid via credit card or COD. No U.S. Postal returns. Be sure to wrap the product or parts securely when shipping to avoid shipping damage.
Policy Statement for Speedball Potter’s Wheel Warranties:
Warranty card must be on file at Speedball Art Products Company
Customer must contact Speedball Art Products Company for Return Authorization Number prior to returning the wheel. Please write the number clearly on the outside of the box.
Parts for warranty repair must be shipped prepaid to Speedball Art Products Company.
Send entire system as a unit control box, motor, foot pedal and all power with no cut cords. Experience has shown that by sending the entire system, repairs are made the first time, made correctly and with less time and trouble for all parties concerned. Full wheel shipments for repair or replacement must be shipped in original packaging.
Enclose a brief description of the problem, along with your name, UPS address, phone number, email address and personal address.
Speedball Art Products Company will pay UPS/FedEx Ground Service shipping back to customer.
Any extra charges due to a request by the customer to rush shipment are to be paid by the customer.
For your convenience, troubleshooting can also be conducted by phone with one of our trained Customer Service Representatives at 800.898.7224, Monday-Friday, 8:00am-5:00pm EST.
Jen-Ken Kiln WarrantyJEN-KEN KILNS are warranted to the original purchaser to be free from defects in materials and workmanship when used under normal and proper conditions for the periods specified below. The warranty period begins at the date of original purchase from JEN-KEN KILNS, a JEN-KEN KILN authorized distributor or dealer.
JEN-KEN KILNS are warranted for 2 years (1 year for the Chili Pepper) from date of original purchase.
Dawson Kiln Sitter is warranted by a separate 1 year warranty from WP Dawson, Inc.
PerfectFire panels are warranted by a separate 1 year plan from the manufacturer.
FireRight panels are warranted by a separate 1 year plan from the manufacturer.
To Claim under the Warranty, the purchaser must:
Provide written proof of the date of purchase.
Notify JEN-KEN KILN (or distributor/dealer) from whom the kiln was purchased.
Make the kiln immediately available for inspection.
FOR WARRANTY REPAIRS:
Warranty repairs should be handled from where you purchased the kiln and they will arrange for any repairs or replacement of parts under the terms of the warranty and upon receipt of the kiln or defective part(s). Warranty work, other than that performed at the factory, DOES NOT include labor, just parts. The defective parts may be returned to JEN-KEN KILNS (postage prepaid) 3615 Ventura Drive West, Lakeland, Florida USA 33811. Include your name and address, a letter of explanation and the name and address from where you purchased the kiln. If, after factory examination the part is found to be defective, a new or repaired part will be sent prepaid by JEN-KEN KILNS.
If the entire kiln is to be returned to the factory, all transportation costs are the responsibility of the purchaser. The purchaser should notify JEN-KEN KILNS (863) 648-0585 prior to shipping. We will advise the best shipping method and if it is necessary to return the whole kiln or only certain parts. Factory warranty work will be performed within 30 days after the defective part is returned to the factory.
JEN-KEN KILN reserves the right, as its option, to replace the entire kiln or any part of it in order to fulfill its obligation under this warranty.
This Warranty DOES NOT Cover:
Kilns altered in any way after leaving our factory.
Abuse or neglect, moisture, improper storage.
Kiln Overfires (exceeding the melting temperatures of the materials being fired) regardless of the cause of the overfire. (This does not occur in kiln that are monitored while firing. If in doubt during a firing, turn the kiln off)
Dawson Kiln Sitter or Limit Timer.
Kilns operated on incorrect voltage.
Improper electrical installation.
Kilns used for purposes other than firing ceramic or glass materials.
Kilns operated in excess of the temperature rating of the kiln.
Damage that may occur from kilns that are fired on or near combustible materials (i.e.: wood floors).
This Warranty is in lieu of all other warranties, expressed or implied. JEN-KEN KILN neither assumes nor authorizes any distributor, dealer, retailer or employee to assume for it any other obligation of liabilities in connection with JENKEN KILNS.
This warranty is limited, as specified above and excludes incidental or consequential damages, so the above limitations or exclusions may not apply to you.
This warranty give you specific rights and you may also have other rights why vary from state to state.
Manufactured by Sir Ramic Porcelain, Inc.
3615 Ventura Drive West Lakeland, Florida USA 33811
Olympic Kilns Warranty
This Warranty Is Applicable to All Kilns Manufactured by Olympic Kilns That Are Used for Ceramics, Pottery and Glass.
Cone 10 Kilns Have a One-Year Warranty and All Other Kilns Have a Two-Year Warranty. Certain Parts, Thermocouple, Kiln Sitter Tube Assembly, Are Not Covered Under Warranty, Nor Is Kiln Furniture.
Haugen Manufacturing, Incorporated guarantees to the original purchaser that any defects in OLYMPIC KILNS which become apparent within two years (one year for the Dawson Kiln Sitter and safety timer which is covered by warranty from W. P. Dawson, Inc. and kilns rated at cone 10) will be remedied as specified below.
Our warranty, of course, does not cover any kiln damaged or altered by you or others after it leaves our factory. Our warranty does not cover damage due to reduction or salt firing, over-firing, exceeding the maximum cone or temperature ratings, improper installation, use of electrical voltages different than those specified, or firing material other than ceramics.
If a defect of manufacturer becomes apparent, and your retailer does not resolve it to your satisfaction, we will in the following manner: Within (6;) days of the first indication of a defect, tell us in writing of defect, and the date, place and proof of the your purchase. We will contact you to determine what parts seem to warrant repair and to instruct you as to shipment of the kiln parts. You will dismantle, package, and ship the parts we request (and no others), to us at your cost, freight prepaid. If the kiln has a defect of manufacture we will repair, replace or refund as is appropriate, within (30) days. We will ship to you at our cost in your package, for you to reinstall at your cost. If the parts shipped by you to us are in need of repair or replacement for something which is not covered by this warranty, we will not perform the work until you have authorized the work and made arrangements for payment. If substantially an entire kiln is returned for repair under warranty, you will prepay the cost of packaging and shipping both to and from the factory.
We shall in no event be liable for injuries to persons or property or for incidental, contingent, special or consequential damages arising from the use of our products. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
HAUGEN MANUFACTURING, INC.
P. O. BOX 1347
4225 THURMON TANNER ROAD FLOWERY BRANCH, GA 30542
Paragon kilns are warranted to the original purchaser by Paragon Industries, L.P. (herein Paragon), subject to the listed exclusions below, to be free of defects in workmanship for the periods specified below. The warranty period begins from date of shipment from the Paragon factory unless date of original purchase from an authorized Paragon distributor or dealer can be established.
QuickFire kilns: 3 months
BlueBirds, HT-series, Home Artist, FiberFuse-16, J-series, KM-Series, SC-series, and Vulcans: 1 year
(Vulcan elements are not warranted.)
Kilns with a maximum temperature rating above 2300ºF (except Dragons, Iguana and Vikings): 1 year
TnF 2 controllers, GF, GL, and Fusion series kilns rated 2000°F or lower and all other kilns not listed in this section with a maximum temperature rated 2300ºF or lower: 2 years
Controllers: Sentry (12 key): 2 ½ years; Sentry Xpress (3 key): the length of the new kiln’s warranty or 1 year on replacement controllers for older kilns.
Dragon, Super Dragon, Iguana and Viking kilns: 2 years. S-Type thermocouple and APM elements fall within the 2 year warranty. Standard elements on these models: 6 months. Sentry controller on these models: 2 ½ years. Type-K thermocouple is not warranted on the Dragon, Iguana and Viking.
These warranty periods apply unless otherwise agreed to in writing.
This warranty excludes: 1) Kilns or furnaces damaged by overfiring (exceeding the melting temperature of the material being fired) regardless of cause of overfiring; 2) Ware, tools, kiln furniture, or anything inside damaged by overfire; 3) Kilns allowed to exceed the maximum temperature shown on kiln’s nameplate, regardless of cause; 4) Kilns subjected to abuse, neglect, freight damage or improper storage; 5) Kilns used for either reduction or salt firing, 6) Kilns damaged by improper electrical installation; 7) Kilns used for purposes other than firing ceramics, glass, heat treating, or the purpose for which it was intended; 8) Element burnout caused by contact with foreign materials; 9) The patented Dawson Kiln Sitter and/or Limit Timer manufactured by W.P. Dawson, Inc., 399 Thor Place, Brea, California 92621.
WARRANTY COVERAGE EXTENDS ONLY TO THE ORIGINAL PURCHASER AND DOES NOT COVER REPLACEMENT OF PARTS THAT ARE, BY THEIR NATURE, EXPENDABLE. THIS WARRANTY IS VOIDED IF THE PRODUCT IS ADVERSELY AFFECTED BY ATTACHING ANY FEATURE OR DEVICE TO IT, OR IS IN ANY WAY TAMPERED WITH OR MODIFIED WITHOUT EXPRESS WRITTEN PERMISSION FROM PARAGON INDUSTRIES, L.P.
Paragon Industries, L.P., will repair or replace any parts that become defective under normal and proper use during the specified period for the kiln purchased, providing the kiln has not been subjected to misuse or the listed exclusions. Paragon will furnish and install replacement parts at the factory with transportation costs to and from the factory paid by the owner; or upon receipt of defective parts at the factory, and after factory examination of the defect, Paragon will furnish replacement parts, complete with installation instructions, shipped postpaid to owner. The warranty on the repaired and/or replaced parts will be limited to the unexpired term of the original warranty.
Any claim for adjustment under this warranty must include name and address of dealer from whom kiln was originally purchased. Repair or replacement of any defective parts shall fulfill all obligations of Paragon. No other obligations or liabilities are assumed in connection with Paragon kilns nor does Paragon Industries, L.P. authorize its distributors or dealers to assume any other obligations or liabilities on its behalf.
THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL PARAGON INDUSTRIES, L.P. BE LIABLE FOR ANY LOSS OF PROFITS OR ANY INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF ANY SUCH DEFECT IN MATERIAL OR WORKMANSHIP. NOTE: SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
This agreement is made in the State of Texas and its validity, construction, and all rights under it will be governed by the laws of the State of Texas. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Paragon Industries, L.P.,
2011 South Town East Blvd.
Mesquite, Texas 75149-1122
Seattle Pottery Supply Kiln Limited Warranty
SEATTLE POTTERY LLC d/b/a “Seattle Pottery Supply” warrants to the original purchaser that this product is free from defects in material workmanship for one year from the date of the first retail purchase from an authorized dealer. Transportation charges on product submitted for repair or replacement under this warranty are the sole responsibility of the purchaser. This warranty only applies to the original purchaser and is not transferable.
UNLESS SPECIFICALLY AUTHORIZED do not Return the Unit to the Place of Purchase.
Seattle Pottery Supply (“SPS”) will repair or replace, at its expense, any defective part upon return, freight prepaid, to an authorized Seattle Pottery Supply Service Center.
A unit provided as an exchange will be subject to the warranty of the original unit. The length of the warranty governing the exchanged unit will remain calculated by reference to the purchase date of the original unit.
This warranty does not cover (1) any defect not reported to an authorized SPS dealer or distributor within 10 days of discovery; (2) Type K Thermocouples; (3) any damage caused by overfiring; (4) products subjected to abnormal strain, freight damage, neglect, abuse, improper storage, failure to follow instructions, or products altered from factory standard condition; (5) products whose identification number has been changed; (6) failures of, or failures caused by, parts or accessories not manufactured or supplied by SPS; (7) kilns used for purposes other than firing ceramic materials; (8) kilns used for reduction or salt firing; (9) repair when normal use has exhausted the life of a part of the equipment as a whole; or (10) failures due to acts of God and other force majeure events beyond the manufacturer’s control.
How To Obtain Warranty Service: Notify SPS or your SPS distributor within 10 days of discovery of any defect. Deliver any defective part, freight prepaid, to an authorized SPS service center. Other Limitations: Any special, incidental, or consequential damages, including property damage, lost profits, loss of use, or other economic loss, are excluded to the full extent permitted by state law. . Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. Any implied warranties, including the implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the duration of this limited warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
State Law Rights: This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
How to Request Warranty Service: All repair work must be authorized, either by SPS, or by an authorized SPS distributor, before the work is done. If you believe your kiln is going to require warranty servicing, the first step is to call the SPS distributor from whom you purchased the kiln. If they are unable to provide or coordinate service, call Seattle Pottery Supply and ask for our Technical Service Department for troubleshooting. 206-587-0570
Notice of Defect may be mailed to:
Seattle Pottery Supply
c/o Warranty and Service
35 S Hanford Street
Seattle, WA 98134